CAN I INSTALL A BATH TUB MYSELF?

Can I Install A Bath Tub Myself?

Can I Install A Bath Tub Myself?

Blog Article

Estimate

Are you on the lookout for details around Tools You Need to Install a New Bathtub ?


How to Install a Bathtub
Setting up a bathtub isn't specifically brain surgery, however it does require strong plumbing, woodworking, as well as in some cases, tiling abilities. Changing an old tub with a new one is also a reasonably challenging project. If the old bathtub is easily available, the task can relocate rapidly; if you have to open up a wall to remove the old bathtub as well as position the brand-new bathtub, the job is much harder. In either instance, the job is within a home handyman's abilities, although you will certainly need an assistant to leave the old tub as well as set in the brand-new one. Make certain you have certified yourself for the work as well as are comfortable trying it. Rather than working with a specialist to take over a halfway-completed task, it is much better to think about employing one prior to you begin. Opportunities are you may require a professional plumber to make tube links.
This short article will certainly assist you mount a new bath tub in your restroom if you have actually already acquired a new tub and also don't require to change the setup of your previous supply of water pipelines.
Your tools as well as material checklist must comprise the following:
  • New Bath tub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipe Caps


  • Removing Old Touches


    If you need to change old taps with new ones as a part of your installment, then the first thing you should do is separate the supply of water. After doing so, activate the faucets to drain any kind of water staying in the system. The procedure of eliminating the existing taps can be fairly troublesome as a result of the limited access that is commonly the case.
    Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the taps. Have a cloth prepared for the remaining water that will certainly come from the pipelines. Once the supply pipelines have been eliminated, use the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from transforming during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any old securing substance.
    Before going on to fit the new faucets, compare the pipe links on the old taps to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.

    Fitting New Touches


    If the tails of the new taps are plastic, after that you will need a plastic adapter to prevent damage to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end offers a link to the current supply pipelines.
    If you need to fit a monobloc, after that you will certainly require lowering couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
    Next off, place the tap in the placing hole in the bath/basin making sure that the washing machines are in location in between the tap as well as the sink. Safeguard the tap in position with the supplier offered backnut. As soon as the faucet is securely in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with typical faucet adapters. The former type needs to be connected to the tap finishes initially, tightening only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.

    Installing the Tub


    Utilizing both wood boards under its feet, place the tub in the needed placement. The wooden boards are useful in equally spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four tiny points.
    The next objective is to guarantee that the bathtub is leveled all round. This can be attained by inspecting the spirit level and also changing the feet on the bathtub till the spirit level reviews level.
    To mount faucets, fit the bottom of the outermost versatile faucet port to the suitable supply pipeline by making a compression join; then do the exact same for the other faucet.
    Turn on the water as well as check all joints and also new pipework for leakages as well as tighten them if essential. Fill up the bathtub and additionally check the overflow electrical outlet and the typical electrical outlet for leaks.
    Ultimately, fix the bathroom paneling as described in the producer's user's manual. Tiling and securing around the bath tub ought to wait till the bathtub has been made use of at the very least once as this will resolve it right into its final setting.

    Planning for the Installation


    First of all, the sustaining frame supplied with the bath must be fitted (if required) according to the producer's directions. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is important to make certain that if the faucet features a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the faucets unit to prevent stress on the bath tub.
    Fit the adaptable tap connectors to the bottom of the two faucets making use of 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet with the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you utilize all of the provided washers.
    Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath must now be ready to be suited its final placement.

    Tiling Around the Bathtub


    In the area where the bath meets the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to crack a stiff seal, creating the water to penetrate the wall in between the bathroom and the tiling, resulting in difficulties with dampness and possible leakages to the ceiling listed below.
    You can choose from a range of coloured sealers to assimilate your components and fittings. They are offered in tubes and also cartridges, and also are capable of sealing spaces as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with spins of drenched paper or soft rope. Bear in mind to constantly fill the bathtub with water before sealing, to enable the activity experienced when the bathtub remains in use. The sealant can break relatively early if you do not take into consideration this motion prior to securing.
    Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also quickly offered on the market. It is a good idea to fit the ceramic tiles utilizing waterproof or water resistant glue and also cement.

    Bathtub Installation


    How Important Is A Bathtub To Your Home?


    High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.


    Install Piping Before Tub


    You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.


    Position the Tub


    Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.



    NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.


    Assemble Drain Connections


    Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.


    Place a Pipe For the Shower Head


    First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.


    Attaching Hot and Cold Water Lines


    Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.


    Install the Spout


    Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.



    NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.


    Check For Leaks


    Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.


    estore the Bathroom Wall


    Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

    https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/


    Installing A Bathtub

    I recently found that entry about How to Install a Bathtub while scouting around the web. Kindly set aside a second to share this blog entry if you enjoyed it. I thank you for reading our article about Installing A Bathtub.




    Set An Appointment


    Report this page